Popular Design for Crimping Tools For Stainless Steel Tube - 2A12/2014/2017/2024 T6/T651 High Hardness Aluminum Alloy Bar Aluminum Bar – Cepheus
Short Description:
Popular Design for Crimping Tools For Stainless Steel Tube - 2A12/2014/2017/2024 T6/T651 High Hardness Aluminum Alloy Bar Aluminum Bar – Cepheus Detail:
2A12/2014/2017/2024 T6/T651 High Hardness Aluminum Alloy Bar Aluminum Bar
2024 aluminum bar, aluminum rod is a typical hard aluminum alloy in the aluminum-copper-magnesium series. Its composition is reasonable and its comprehensive performance is good. This alloy is produced in many countries and is the largest amount of hard aluminum.
The alloy can be used as working parts below 150 ° C. The strength of 2024 alloy is higher than that of 7075 alloy. The forming performance is better in the hot state, annealing and new quenching states, and the heat treatment strengthening effect is significant, but the heat treatment process is strict. Poor corrosion resistance, but covered with pure aluminum can be effectively protected; cracks are easy to occur during welding, but special processes can be used for welding and riveting.
2024 aluminum bar,aluminum rod is a high-strength hard aluminum, which can be strengthened by heat treatment. It has moderate plasticity in the quenched and freshly quenched state. It has good spot welding and has the tendency to form intergranular cracks when gas welding. The cutting performance is good, and the machinability after annealing is low: the corrosion resistance is not high. Anodizing treatment and painting methods are often used or the surface is coated with an aluminum layer to improve its corrosion resistance.
2024 is mainly used to make various high-load parts and components (but not including stamping parts and forgings) such as skeleton parts, skins, bulkheads, ribs, spar, rivets and other working parts below 150 ºC on aircraft.
Chemical Composition
| Alloy | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Al |
| 2024 | 0.5 | 0.5 | 3.8-4.9 | 0.3-0.9 | 1.2-1.8 | 0.10 | 0.25 | 0.15 | remain |
Mechanical Properties
| Aluminum Alloy & Temperature | Tensile Strength (Rm/MPa) |
Proof Strength (Rp0.20/Mpa) |
Percentage Elongation (%) |
Hardness (HB) |
| 2024 | 470 | 325 | 10 | 120 |
Product detail pictures:
Related Product Guide:
ZK International Group CO Ltd | Stainless Steel Pipe Fittings
Rosie on the house: Can snow damage my flat roof? | Home & Garden | Stainless Steel Elbow For Helium
Our advantages are lessen charges,dynamic income team,specialized QC,sturdy factories,premium quality services for Popular Design for Crimping Tools For Stainless Steel Tube - 2A12/2014/2017/2024 T6/T651 High Hardness Aluminum Alloy Bar Aluminum Bar – Cepheus, The product will supply to all over the world, such as: Holland, Bangladesh, New Zealand, All our products are exported to clients in the UK, Germany, France, Spain, the USA, Canada, Iran, Iraq, the Middle East and Africa. Our products are well welcomed by our customers for the high quality, competitive prices and the most favorable styles. We hope to establish business relationship with all customers and bring more beautifu colors for the life.
Material Grade
| Material | ASTM A240 Standard | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410S 430 904L |
| ASTM A480 Standard | 302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615,S33228, S38100, 304H, 309H, 310H, 316H, 309HCb, 310HCb, 321H,347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S33228, S34565, S35315,S31200, S31803, S32001, S32550, S31260, S32003, S32101,S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| JIS 4304-2005 Standard | SUS301L,SUS301J1,SUS302,SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| JIS G4305 Standard | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu,SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2,SUS305, SUS309S, SUS310S, SUS312L, SUS315J1, SUS315J2,SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1,SUS316J1L,SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2,SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J4L, SUS405, SUS410L, SUS429, SUS430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L,SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403,SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Product Specification
| Finish | Thickness | Characteristics | Applications |
| No. 1 | 3.0mm~50.0mm | Finished by hot-rolling, annealing and pickling, characterized by white pickled surface | Chemical industry equipment, Industrial tanks |
| No. 2B | 0.3mm~6.0mm | Finished by heat treatment, pickling after cold rolling, followed by skin pass line to be more brighter and smooth surface | General Application Medical Instruments, Tableware |
| No. BA (Bright Annealed) | 0.5mm~2.0mm | Bright heat treatment after cold rolling | Kitchen utensil, kitchen ware, architectural purpose |
| No. 4 | 0.4mm~3.0mm | Polishing with No. 150 to No.180 mesh abrasives. The most popular finishes | Milk & Food processing facilities, Hospital Equipment, Bath-tub |
| No. 8 | 0.5mm~2.0mm | A mirror-like reflective surface by polishing with finer abrasives over 800 mesh | Reflector, Mirror, Interior-Exterior decoration forbuilding |
| HL(Hair Line) | 0.4mm~3.0mm | Finished by continuous linear polishing | Architectural purposes, escalators, kitchen ware vehicles |
Chemical Composition
|
Grade |
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
Ti |
N |
Cu |
Nb |
|
201 |
≤0.15 |
≤1.0 |
5.50-7.50 |
≤0.05 |
≤0.03 |
16.00-18.00 |
3.50-5.50 |
- |
- |
0.05-0.25 |
- |
- |
|
202 |
≤0.15 |
≤1.0 |
7.50-10.00 |
≤0.05 |
≤0.03 |
17.00-19.00 |
4.00-6.00 |
- |
- |
0.05-0.25 |
- |
- |
|
301 |
≤0.15 |
≤1.0 |
≤2.0 |
≤0.045 |
≤0.03 |
16.00-18.00 |
6.00-8.00 |
- |
- |
≤0.1 |
- |
- |
|
302 |
≤0.15 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
8.00-10.00 |
- |
- |
≤0.1 |
- |
- |
|
303 |
≤0.15 |
≤1.0 |
≤2.0 |
≤0.2 |
≥0.15 |
17.00-19.00 |
8.00-10.00 |
≤0.6 |
- |
≤0.1 |
- |
- |
|
304 |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
8.00-10.00 |
- |
- |
- |
- |
- |
|
304L |
≤0.03 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
18.00-20.00 |
8.00-10.00 |
- |
- |
- |
- |
- |
|
304H |
0.04-0.1 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
18.00-20.00 |
8.00-10.00 |
- |
- |
- |
- |
- |
|
304N |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
18.00-20.00 |
8.00-10.00 |
- |
- |
0.10-0.16 |
- |
- |
|
304J1 |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
18.00-20.00 |
6.00-9.00 |
- |
- |
- |
1.00-3.00 |
- |
|
305 |
≤0.12 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
10.50-13.00 |
- |
- |
- |
- |
- |
|
309S |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
22.00-24.00 |
12.00-15.00 |
- |
- |
- |
- |
- |
|
310S |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
24.00-26.00 |
19.00-22.00 |
- |
- |
- |
- |
- |
|
316 |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
10.00-14.00 |
2.00-3.00 |
- |
- |
- |
- |
|
316L |
≤0.03 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
12.00-15.00 |
2.00-3.00 |
- |
- |
- |
- |
|
316H |
≤0.1 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
10.00-14.00 |
2.00-3.00 |
- |
- |
- |
- |
|
316N |
≤0.03 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
10.00-14.00 |
2.00-3.00 |
- |
0.10-0.16 |
- |
- |
|
316Ti |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
16.00-19.00 |
11.00-14.00 |
2.00-3.00 |
≥5C |
- |
- |
- |
|
317L |
≤0.03 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
18.00-20.00 |
11.00-15.00 |
3.00-4.00 |
- |
- |
- |
- |
|
321 |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
9.00-12.00 |
- |
5C-0.7 |
- |
- |
- |
|
347 |
≤0.08 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
9.00-12.00 |
- |
- |
- |
- |
10C-1.10 |
|
347H |
≤0.1 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
9.00-12.00 |
- |
- |
- |
- |
8C-1.10 |
|
2205 |
≤0.03 |
≤1.0 |
≤2.0 |
≤0.035 |
≤0.03 |
21.00-24.00 |
4.50-6.50 |
2.50-3.50 |
- |
0.08-0.20 |
- |
- |
|
2507 |
≤0.03 |
≤0.8 |
≤1.2 |
≤0.035 |
≤0.02 |
24.00-26.00 |
6.00-8.00 |
3.00-5.00 |
- |
0.24-0.32 |
- |
- |
|
904L |
≤0.02 |
≤1.0 |
≤2.0 |
≤0.045 |
≤0.03 |
19.00-23.00 |
23.00-28.00 |
4.00-5.00 |
- |
- |
1.00-2.00 |
- |
|
C276 |
≤0.02 |
≤0.05 |
≤1.0 |
- |
- |
14.00-16.50 |
Other |
- |
- |
- |
- |
- |
|
Monel400 |
≤0.3 |
≤0.5 |
≤2.0 |
- |
≤0.024 |
- |
≥63 |
- |
- |
- |
28-34 |
- |
|
409L |
≤0.03 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
17.00-19.00 |
- |
- |
- |
- |
- |
- |
|
410 |
≤0.15 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
11.50-13.50 |
- |
- |
- |
- |
- |
- |
|
410L |
≤0.03 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
11.50-13.50 |
- |
- |
- |
- |
- |
- |
|
420J1 |
0.16-0.25 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
12.00-14.00 |
- |
- |
- |
- |
- |
- |
|
420J2 |
0.26-0.40 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
12.00-14.00 |
- |
- |
- |
- |
- |
- |
|
430 |
≤0.12 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
- |
- |
- |
- |
- |
- |
|
436L |
≤0.025 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-19.00 |
- |
- |
- |
- |
- |
- |
|
439 |
≤0.03 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
- |
- |
- |
- |
- |
- |
|
440A |
0.60-0.75 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
- |
≤0.75 |
- |
- |
- |
- |
|
440B |
0.75-0.95 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
- |
≤0.75 |
- |
- |
- |
- |
|
440C |
0.95-1.2 |
≤1.0 |
≤1.0 |
≤0.035 |
≤0.03 |
16.00-18.00 |
- |
≤0.75 |
- |
- |
- |
- |
|
441 |
≤0.03 |
0.2-0.8 |
≤0.7 |
≤0.03 |
≤0.015 |
17.50-18.50 |
- |
≤0.5 |
0.1-0.5 |
≤0.025 |
- |
0.3+3C-0.9 |
We wrap the stainless steel products with anti-rust paper and steel rings to prevent damage.
Identification labels are tagged accordingto standard specification or customer’s instructions.
Special packing is available as per customer’s requirement.
Stainless Steel Coil Package
Stainless Steel Sheet / Stainless Steel Plate Package
Stainless Steel Strip Package
Shipment Package
Our company is based in Wuxi, gathering city of industrial stainless steel in China.
We specialized in stainless coils, sheets and plate, stainless steel pipe and fittings, stainless steel tubes, and also aluminum products and copper products.
Our products have been highly praised by our clients from Europe, America, the Middle East, African and Southeast Asia. We will offer competitive products and comprehensive service to customers.
Stainless Steel Grade: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 316L, 321, 347, 410, 416, 420, 430, 430F, 440, 440c,
Alloy Grade :Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanium, Tantalum, High Speed Steel, Mild Steel, Aluminium, Alloy Steel, Carbon Steel, Special Nickel Alloys
In form of : Round Bars, Square Bars, Hexagonal Bars, Flat Bars, Angles, Channels, Profiles, Wires, Wire Rods, Sheets, Plates, Seamless Pipes, ERW Pipes, Flanges, Fittings,etc.
Q1: What is stainless?
A: Stainless means no marks on the steel surface, or a kind of steel that is not damaged by air or water and that does not change color, spotless, resistant to staining, rusting, the corrosive effect of chemicals.
Q2: Does stainless mean no rusting?
A: No, stainless means not easy to get stained or rusty, it has speical ability to reisist staining, rusting and corrosion.
Q3: Do you supply stainless steel sheets?
A: Yes, we supply different types of stainless steel sheets, with thickness ranges from 0.3-3.0mm. and in different finishes.
Q4: Do you accept cut to length service?
A: Of course, customer’s satisfaction is our top priority.
Q5: If i have a small order, do you accept small order?
A: Not a problem, your concern is our concern, small quantities are accepted.
Q6: How can you guarantee your product quality?
A: First, from the very start, we have already implemented a spirit to their mind, that is quality is life, our professional workers and staffs will follow up every step till the goods packed well and shipped out.
Q7: Will you pack the products?
A: Professional people do professional packing, we have different types of packing optional to customers, economic one or better one.
Q8: What do you need to know from customer before accurate quotation?
A: For an accurate quotation, we need to know grade, thickness, size, surface finish, color and quantity of your order, and also the destination of the goods. Customized product information will be needed more, like drawing, layout and plan. Then we will offer competitive quotation with the above information.
Q9: What kind of payment term you accpet?
A: We accept T/T, West union, L/C.
Q10: If this is a small order, will you delivery the goods to our agent?
A: Yes, we are born to solve problems of our customers, we will get the goods safely to your agent’s warehouse and send you the pictures.
Q11: Do you just make flat sheet? I want to make a fabrication for my new project.
A: No, we mainly produce stainless steel flat sheet surface treatment, at the same time, we manufacture customized metal finished product as per customer’s drawing and plan, our technician will take care of the rest.
Q12: How many coutries you already exported ?
A: Exported to more than 50 countries mainly from America, Russia, UK, Kuwait, Egypt, Iran,
Turkey, Jordan, etc.
Q13: How can I get some samples?
A: Small samples in store and can provide the samples for free. Catalgue is available, most
patterns we have ready samples in stock. Customized samples will take about 5-7days.
Q14: What is the delivery ?
A: Sample order’s delivery time is 5- 7 days. Container orders are about 15-20 days.
Q15: What is the application about your Products?
A: 1.elevator door/cabin or and escalator’s side-wall.
2.Wall cladding inside or outside meeting room/ restaurant.
3.Facade when cladding over something, like columns in the lobby.
4.Ceiling in the supermarket. 5.Decorative draws in some entertainment places.
Q16: How long Can You Guarantee for This Product/Finish?
A: Color guarantee for more than 10 years. Original materials quality certificate can
be provided.
By Salome from Mexico - 2015.06.18 17:25
The company has a good reputation in this industry, and finally it tured out that choose them is a good choice.
By Johnny from Qatar - 2016.10.13 10:47
