Ndodo Zosapanga dzimbiri za 304H
Kufotokozera Kwachidule:
Ndodo Zosapanga dzimbiri za 304H
Ndodo Zosapanga dzimbiri za 304HKufotokozera
Standard: ASTM A276 / A479, ASME SA276 / A479
Round Bar Kukula: 3mm ~ 800mm
Square Bar Kukula: 4mm * 4mm ~ 100mm * 100mm
Flat Bar Kukula: 2mm ~ 100mm
Hex Bar Kukula: 2mm ~ 100mm
Makulidwe: 50 mm mpaka 6000 mm kutalika
Utali: 1 mpaka 6 Mamita, Kudula Mwamakonda Utali
Fomu: Round, Square, Hex(A/F), Rectangle, Billet, Ingot, Forging etc.
Magiredi Ofanana a SS 304H Threaded Rods
| ZOYENERA | Mbiri ya WERKSTOFF NR. | UNS |
| Chithunzi cha SS304H | 1.4948 | S30409 |
Chitsulo Chosapanga dzimbiri 304H Ndodo Yopangiras Chemical Composition
| Chinthu | Chithunzi cha SS304H |
| C | 0.10 max |
| Mn | 2.0 max |
| Si | 0.75 max |
| P | 0.045 kukula |
| S | 0.03 max |
| Cr | 18-20 |
| Ni | 8 - 10.5 |
Katundu Wamakina a SS 304H Threaded Ndodo
| Chinthu | Chithunzi cha SS304H |
| Kuchulukana | 8.0g/cm3 |
| Melting Point | 1400 °C (2550 °F) |
| Kulimba kwamakokedwe | Psi – 75000 , MPa – 515 |
| Mphamvu Zokolola (0.2% Offset) | Psi – 30000, MPa – 205 |
| Elongation | 40% |
Mitundu ya SS 304H Threaded Ndodo
Chitsulo Chosapanga dzimbiri 304H Ndodo Yopangiras
SS 304H Mapeto Awiri Mapeto Ndodo
Zopangira Zopangira SS 304H
SS 304H Wopukutidwa Ndodo Zazingwe
Mbiri ya WERKSTOFF NR. 1.4948 Ndodo Zamtundu
SS 304H Mapeto Amodzi Mapeto Opangira Ndodo
Chitsulo Chosapanga dzimbiri 304H Zonse Zili ndi Zingwe Zopanda Zingwe
Ndodo Zachitsulo Zosapanga dzimbiri za 304H
SS 304H Ndodo Zamtundu
Ndodo za A276 SS 304H
SS 304H Ndodo Zokwanira Zonse
SS 304H Ndodo Zopangidwa Zonse
Zopangira SS 304H Zokwanira Zokwanira
SS 304H Yopukutidwa Ndi Ndodo Zokwanira
UNS S30409 Ndodo Zokwanira Zonse
Mbiri ya WERKSTOFF NR. 1.4948 Ndodo Zokwanira Kwambiri
SS 304H Yopangidwa Ndi Zingwe Zokhazikika
SS 304H Ndodo Zotalika Mokwanira
SS 304H Fine Threaded Ndodo
SS 304H Ndodo Zokwanira Zonse
A276 SS 304H Ndodo Zokwanira Zonse
SS 304H Zozizira Zozizira Zozungulira
SS 304H CR Ndodo Zopangira Magalasi
Tumizani Ndodo Zachipolishi SS 304H CR
SS 304H Cold Anagulung'undisa Mapeto Amodzi Ndodo Zazingwe
UNS S30409 Ndodo Zozizira Zozizira
Mbiri ya WERKSTOFF NR. 1.4948 Cold Rolled Threaded Ndodo
SS 304H Cold Adagubuduza Ndodo Zopangira Zabwino
SS 304H Cold Yokulungidwa Pawiri End Threaded Ndodo
SS 304H Cold Yogubuduza Ndodo Zazingwe Zazitali
SS 304H Zozizira Zozizira Zozungulira
A276 SS 304H Ndodo Zozizira Zozizira
SS 304H Ndodo Zotentha Zotentha
SS 304H Yotentha Yokulungidwa Ndodo Zopangira Zabwino
SS 304H HR Ndodo Zopangira Magalasi
Tumizani Ndodo Zachipolishi za SS 304H HR
UNS S30409 Ndodo Zotentha Zotentha
Mbiri ya WERKSTOFF NR. 1.4948 Ndodo Zozizira Zotentha
SS 304H Yotentha Yokulungidwa Ndodo Zazingwe Zazitali
SS 304H Yotentha Yokulungidwa Mapeto Amodzi Ndi Ndodo Zopangira
SS 304H Yotentha Yokulungidwa Pawiri End Threaded Ndodo
SS 304H Ndodo Zotentha Zotentha
A276 SS 304H Ndodo Zotentha Zotentha
Maphunziro a Zinthu
| Zakuthupi | ASTM A240 Standard | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 4309 |
| ASTM A480 muyezo | 302. 347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S30601 03, S32001, S32550, S31260, S32003, S32101,S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| JIS 4304-2005 Standard | SUS301L,SUS301J1,SUS302,SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| JIS G4305 Standard | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu,SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2,SUS305, SUS304S, SUS301S 15J2,SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1,SUS316J1L, SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2,SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3US44, SUS404, SUS294, SUS294 SUS430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L,SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403,SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Mafotokozedwe a Zamalonda
| Malizitsani | Makulidwe | Makhalidwe | Mapulogalamu |
| Nambala 1 | 3.0mm ~ 50.0mm | Anamaliza ndi otentha anagubuduza, annealing ndi pickling, yodziwika ndi woyera kuzifutsa pamwamba | Zida zamakampani a Chemical, akasinja a Industrial |
| Nambala 2B | 0.3mm ~ 6.0mm | Anamaliza ndi kutentha mankhwala, pickling pambuyo ozizira anagubuduza, kenako khungu chikudutsa mzere kukhala kwambiri owala ndi yosalala pamwamba | General Application Medical Instruments, Tableware |
| BA (Bright Annealed) | 0.5mm ~ 2.0mm | Bright kutentha mankhwala pambuyo ozizira anagubuduza | Chiwiya cha khitchini, khitchini yogulitsira, cholinga cha zomangamanga |
| Nambala 4 | 0.4mm ~ 3.0mm | Kupukuta ndi No. 150 mpaka No.180 mauna abrasives. Zomaliza zodziwika kwambiri | Malo opangira mkaka & Chakudya, Zida Zachipatala, Bath-tub |
| Nambala 8 | 0.5mm ~ 2.0mm | Malo owoneka ngati galasi popukutidwa ndi zomatira zabwino kwambiri kuposa mauna 800 | Reflector, Mirror, Mkati-Zokongoletsa Zakunja zomanga |
| HL (Mzere Watsitsi) | 0.4mm ~ 3.0mm | Kumalizidwa ndi kupukuta kosalekeza kwa mzere | Zolinga zomanga, ma escalator, magalimoto akukhitchini |
Chemical Composition
| Gulu | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304l pa | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304j1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309s ndi | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310s | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316l ndi | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316 ndi | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317l ndi | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C-1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904l pa | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Zina | - | - | - | - | - |
| Monel400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409l ndi | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410l pa | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420j1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420j2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436l ndi | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440b | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3+3C-0.9 |
Ifekukulunga zitsulo zosapanga dzimbiri ndi mapepala odana ndi dzimbiri ndi mphete zachitsulo kuti zisawonongeke.
Zozindikiritsa zimayikidwa molingana ndi zomwe kasitomala akufuna.
Kulongedza kwapadera kulipo monga momwe kasitomala amafunira.
Phukusi la Chitsulo Chosapanga dzimbiri
Phukusi lachitsulo chosapanga dzimbiri / Phukusi la chitsulo chosapanga dzimbiri
Phukusi Lazitsulo Zosapanga dzimbiri
Phukusi Lotumiza
Kampani yathu ili ku Wuxi, kusonkhanitsa mzinda wazitsulo zosapanga dzimbiri ku China.
Tinkapanga ma coils osapanga dzimbiri, mapepala ndi mbale, chitoliro chachitsulo chosapanga dzimbiri ndi zomangira, machubu achitsulo chosapanga dzimbiri, komanso zinthu za aluminiyamu ndi zinthu zamkuwa.
Zogulitsa zathu zayamikiridwa kwambiri ndi makasitomala athu ochokera ku Europe, America, Middle East, Africa ndi Southeast Asia. Tidzapereka zinthu zampikisano komanso ntchito zambiri kwa makasitomala.
Gulu la Zitsulo Zosapanga dzimbiri: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 3160, 4, 4, 4, 4, 4 0, 430F, 440, 440c,
Gulu la Aloyi: Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanium, Tantalum, High Speed Steel, Mild Steel, Aluminium, Alloy Steel, Carbon Steel, Special Nickel Alloys
Mu mawonekedwe a : Mipiringidzo Yozungulira, Mipiringidzo ya Square, Mipiringidzo ya Hexagonal, Mipiringidzo Yathyathyathya, Ngongole, Makanema, Mbiri, Mawaya, Ndodo Zawaya, Mapepala, Mbale, Mipope Yopanda Msoko, Mapaipi a ERW, Flanges, Fittings, etc.
Q1: Kodi zosapanga dzimbiri ndi chiyani?
Yankho: Zopanda banga zimatanthauza kuti palibe chizindikiro pamwamba pa chitsulo, kapena chitsulo chosawonongeka ndi mpweya kapena madzi ndipo sichisintha mtundu, chopanda banga, chosagonjetsedwa ndi madontho, dzimbiri, kuwononga kwa mankhwala.
Q2: Kodi zosapanga dzimbiri zikutanthauza kuti palibe dzimbiri?
Yankho: Ayi, zosapanga dzimbiri sizitanthauza kuti ndizosavuta kuti zikhale zodetsedwa kapena dzimbiri, zimakhala ndi mphamvu zapadera zokana madontho, dzimbiri ndi dzimbiri.
Q3: Kodi mumapereka zitsulo zosapanga dzimbiri?
A: Inde, timapereka mitundu yosiyanasiyana yazitsulo zosapanga dzimbiri, zokhala ndi makulidwe a 0.3-3.0mm. ndi muzomaliza zosiyanasiyana.
Q4: Kodi mumavomereza ntchito yodula mpaka kutalika?
A: Zoonadi, kukhutira kwamakasitomala ndizofunika kwambiri.
Q5: Ngati ndili ndi oda yaying'ono, kodi mumavomereza oda yaying'ono?
A: Osati vuto, nkhawa yanu ndi nkhawa yathu, zochepa zimavomerezedwa.
Q6: Kodi mungatsimikizire bwanji kuti malonda anu ali abwino?
Yankho: Choyamba, kuyambira pachiyambi, takhazikitsa kale mzimu m'maganizo mwawo, womwe ndi moyo wabwino, antchito athu akatswiri ndi ndodo azitsata gawo lililonse mpaka katundu atalongedza bwino ndikutumizidwa kunja.
Q7: Kodi mudzanyamula katundu?
A: Anthu aluso amalongedza akatswiri, tili ndi mitundu yosiyanasiyana yonyamula mwakufuna kwa makasitomala, yachuma kapena yabwinoko.
Q8: Kodi muyenera kudziwa chiyani kuchokera kwa kasitomala musanayambe mawu olondola?
Yankho: Kuti tipeze mawu olondola, tiyenera kudziwa giredi, makulidwe, kukula, kumaliza kwapamwamba, mtundu ndi kuchuluka kwa oda yanu, komanso komwe katundu akupita. Zambiri zazinthu zosinthidwa makonda zidzafunikanso, monga kujambula, masanjidwe ndi mapulani. Kenako tipereka mawu opikisana ndi zomwe zili pamwambapa.
Q9: Ndi nthawi yanji yolipira yomwe mumavomereza?
A: Timavomereza T/T, West union, L/C.
Q10: Ngati ili ndi dongosolo laling'ono, kodi mungatumize katunduyo kwa wothandizira wathu?
A: Inde, tinabadwa kuti tithetse mavuto a makasitomala athu, tidzatenga katunduyo mosamala kumalo osungira katundu wa wothandizira wanu ndikukutumizirani zithunzi.
Q11: Kodi mumangopanga pepala lathyathyathya? Ndikufuna kupanga zongopeka za polojekiti yanga yatsopano.
A: Ayi, makamaka timatulutsa zitsulo zosapanga dzimbiri lathyathyathya pamwamba mankhwala, nthawi yomweyo, timapanga makonda zitsulo zomalizidwa mankhwala malinga ndi zojambula ndi dongosolo kasitomala, katswiri wathu adzasamalira zina.
Q12: Ndi ma coutries angati omwe mudatumiza kale kunja?
A: Amatumizidwa kumayiko opitilira 50 makamaka ochokera ku America, Russia, UK, Kuwait, Egypt, Iran,
Turkey, Jordan, etc.
Q13: Ndingapeze bwanji zitsanzo?
A: Zitsanzo zazing'ono zomwe zili m'sitolo ndipo zimatha kupereka zitsanzo kwaulere. Catalgue ilipo, ambiri
mapatani tili ndi zitsanzo okonzeka katundu. Zitsanzo zosinthidwa zidzatenga pafupifupi 5-7days.
Q14: Kutumiza ndi chiyani?
A: Nthawi yobweretsera yachitsanzo ndi masiku 5- 7. Kulamula kwa chidebe ndi pafupifupi masiku 15-20.
Q15: Kodi ntchito ndi Zogulitsa zanu ndi ziti?
A: 1. chitseko chitseko / kanyumba kapena ndi escalator mbali-khoma.
2.Kuvala khoma mkati kapena kunja kwa chipinda chochitira misonkhano/malo odyera.
3.Facade pamene mukuphimba chinachake, monga mizati m'chipinda cholandirira alendo.
4.Ceiling mu supermarket. 5.Decorative imajambula m'malo ena osangalatsa.
Q16: Kodi Mungatsimikize Kwanthawi yayitali Bwanji Pazamalonda / Kumaliza?
A: Chitsimikizo cha utoto kwa zaka zopitilira 10. Satifiketi yapamwamba ya zida zoyambira imatha
kuperekedwa.
