304 coil ta 'l-istainless steel POSCO
Deskrizzjoni qasira:
stainless steel cold rolled coil tintuża ħafna fil-kostruzzjoni, kirurġija, essenzjali tal-kċina, eċċ 304 stainless steel huwa adattat għall-kostruzzjoni ta 'banisters esterni u poġġamani, u għandu prestazzjoni tajba ta' pproċessar u weldability.
Stainless Steel coil
Il-coil ta 'l-istainless steel jista' jsir permezz ta 'rolling bis-sħana u rolling kiesaħ, inkluża l-ħxuna ta' folja ta '0.31-3.0 mm u pjanċa ta' 3.0-30 mm.
L-istainless steel irrumblat bis-sħana mhuwiex tajjeb daqs ir-rumblat fil-kesħa fi proprjetajiet mekkaniċi, iżda hemm toughness u duttilità tajba. Il-pjanċa tal-istainless steel rrumblata fil-kesħa hija baxxa fit-toughness minħabba t-twebbis tajjeb.
Sabiex tiġi żgurata kull tip ta 'saħħa ta' rendiment ta 'l-istainless steel, saħħa tat-tensjoni, titwil u ebusija u proprjetajiet mekkaniċi oħra biex jissodisfaw ir-rekwiżiti, qabel il-kunsinna għandha tkun ittemprar ta' l-istainless steel, trattament ta 'soluzzjoni, trattament tas-sħana li qed tixjieħ.
Grad tal-Materjal
| Materjal | Standard ASTM A240 | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410 409S |
| Standard ASTM A480 | 302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615, S33228, S38100, 304H, 309H, 316H1b, 3161Hb, 310H3, 310H3 347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S334525, S334525, S334525, S334528 03, S32001, S32550, S31260, S32003, S32101, S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| JIS 4304-2005 Standard | SUS301L, SUS301J1, SUS302, SUS304, SUS304L, SUS316/316L, SUS309S,SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| JIS G4305 Standard | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu, SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2, SUS305, SUS3013S, SUS311S, SUS311S 15J2, SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1, SUS316J1L, SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2, SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J3L, SUS324, SUS34, SUS34, SUS34 430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L, SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403, SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Speċifikazzjoni tal-Prodott
| Temm | Ħxuna | Karatteristiċi | Applikazzjonijiet |
| Nru 1 | 3.0mm ~ 50.0mm | Lest minn hot-rolling, ittemprar u pickling, ikkaratterizzat minn wiċċ imnaddfin abjad | Tagħmir għall-industrija kimika, Tankijiet industrijali |
| Nru 2B | 0.3mm ~ 6.0mm | Lest bi trattament bis-sħana, pickling wara rolling kiesaħ, segwit minn linja ta 'pass tal-ġilda biex tkun wiċċ aktar isbaħ u lixx | Applikazzjoni Ġenerali Strumenti Mediċi, Oġġetti tal-mejda |
| Nru BA (Ttemprat Brillant) | 0.5mm ~ 2.0mm | Trattament tas-sħana qawwi wara rolling kiesaħ | Utensili tal-kċina, oġġetti tal-kċina, skop arkitettoniku |
| Nru 4 | 0.4mm ~ 3.0mm | Illustrar b'abrażivi tal-malji Nru 150 sa No.180. L-iktar finituri popolari | Faċilitajiet għall-ipproċessar tal-Ħalib u l-Ikel, Tagħmir tal-Isptar, Bath-tub |
| Nru 8 | 0.5mm ~ 2.0mm | Wiċċ li jirrifletti qisu mera bl-illustrar b'abrażivi ifjen ta 'aktar minn 800 malja | Riflettur, mera, dekorazzjoni ta 'ġewwa-barra għall-bini |
| HL (Linja tax-xagħar) | 0.4mm ~ 3.0mm | Lest minn illustrar lineari kontinwu | Għanijiet arkitettoniċi, skalaturi, vetturi tal-oġġetti tal-kċina |
Daqsijiet standard
| Daqs | Ħxuna: 0.15mm-3.00mm (folji Irrumblati kiesaħ); 4-30mm (pjanċa rrumblata bis-sħana) |
| Wisa ': 1000mm, 1219mm, 1250mm, 1500mm, 1800mm, 2000mm | |
| Tul: bħala kolji |
Kompożizzjoni kimika
| Grad | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304J1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316Ti | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C-1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904L | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Oħrajn | - | - | - | - | - |
| Monel400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420J1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420J2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436L | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440B | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3 + 3C-0.9 |
Grad tal-Materjal
| Materjal | Standard ASTM A240 | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410 409S |
| Standard ASTM A480 | 302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615, S33228, S38100, 304H, 309H, 316H1b, 3161Hb, 310H3, 310H3 347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S334525, S334525, S334525, S334528 03, S32001, S32550, S31260, S32003, S32101, S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| JIS 4304-2005 Standard | SUS301L, SUS301J1, SUS302, SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| JIS G4305 Standard | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu, SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2, SUS305, SUS3013S, SUS311S, SUS311S 15J2, SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1, SUS316J1L, SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2, SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J3L, SUS324, SUS34, SUS34, SUS34 430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L, SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403, SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Speċifikazzjoni tal-Prodott
| Temm | Ħxuna | Karatteristiċi | Applikazzjonijiet |
| Nru 1 | 3.0mm ~ 50.0mm | Lest minn hot-rolling, ittemprar u pickling, ikkaratterizzat minn wiċċ imnaddfin abjad | Tagħmir għall-industrija kimika, Tankijiet industrijali |
| Nru 2B | 0.3mm ~ 6.0mm | Lest bi trattament bis-sħana, pickling wara rolling kiesaħ, segwit minn linja ta 'pass tal-ġilda biex tkun wiċċ aktar isbaħ u lixx | Applikazzjoni Ġenerali Strumenti Mediċi, Oġġetti tal-mejda |
| Nru BA (Ttemprat Brillant) | 0.5mm ~ 2.0mm | Trattament tas-sħana qawwi wara rolling kiesaħ | Utensili tal-kċina, oġġetti tal-kċina, skop arkitettoniku |
| Nru 4 | 0.4mm ~ 3.0mm | Illustrar b'abrażivi tal-malji Nru 150 sa No.180. L-iktar finituri popolari | Faċilitajiet għall-ipproċessar tal-Ħalib u l-Ikel, Tagħmir tal-Isptar, Bath-tub |
| Nru 8 | 0.5mm ~ 2.0mm | Wiċċ li jirrifletti qisu mera bl-illustrar b'abrażivi ifjen ta 'aktar minn 800 malja | Riflettur, mera, dekorazzjoni ta 'ġewwa-barra għall-bini |
| HL (Linja tax-xagħar) | 0.4mm ~ 3.0mm | Lest minn illustrar lineari kontinwu | Għanijiet arkitettoniċi, skalaturi, vetturi tal-oġġetti tal-kċina |
Kompożizzjoni Kimika
| Grad | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304J1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316Ti | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C-1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904L | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Oħrajn | - | - | - | - | - |
| Monel400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420J1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420J2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436L | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440B | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3 + 3C-0.9 |
AħnaKebbeb il-prodotti tal-istainless steel b'karta kontra s-sadid u ċrieki tal-azzar biex tevita l-ħsara.
It-tikketti ta 'identifikazzjoni huma mmarkati skond l-ispeċifikazzjoni standard jew l-istruzzjonijiet tal-klijent.
Ippakkjar speċjali huwa disponibbli skont il-ħtieġa tal-klijent.
Stainless Steel Coil Pakkett
Folja tal-Azzar Stainless / Pakkett tal-Pjanċa tal-Azzar Stainless
Pakkett tal-Istrixxa tal-Azzar li ma jsaddadx
Pakkett tal-Ġarr
Kumpanija tagħna hija bbażata f'Wuxi, ġbir belt ta 'l-istainless steel industrijali fiċ-Ċina.
Aħna speċjalizzati f'coils, folji u pjanċa tal-istainless steel, pajpijiet u fittings tal-istainless steel, tubi tal-istainless steel, u wkoll prodotti tal-aluminju u prodotti tar-ram.
Il-prodotti tagħna ġew imfaħħra ħafna mill-klijenti tagħna mill-Ewropa, l-Amerika, il-Lvant Nofsani, l-Afrika u l-Asja tax-Xlokk. Aħna se noffru prodotti kompetittivi u servizz komprensiv lill-klijenti.
Stainless Steel Grad: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 316L, 316, 316, 4, 1, 4, 3, 4 , 430F, 440, 440c,
Grad ta' Liga: Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanju, Tantalu, Azzar b'Veloċità Għolja, Azzar ħafif, Aluminju, Azzar Liga, Azzar tal-Karbonju, Ligi speċjali tan-nikil
F'forma ta ': Vireg Tondi, Vireg Pjazza, Vireg Eżagonali, Vireg Ċatti, Angoli, Kanali, Profili, Wajers, Vireg tal-Wajer, Folji, Pjanċi, Pajpijiet mingħajr saldatura, Pajpijiet ERW, Flanġijiet, Fittings, eċċ.
Q1: X'inhu l-istainless steel?
A: Stainless tfisser l-ebda marki fuq il-wiċċ ta ' l-azzar, jew tip ta ' azzar li ma ssirx ħsara bl-arja jew ilma u li ma jbiddilx il-kulur, bla tebgħa, reżistenti għat-tbajja ', rusting, l-effett korrużiv tal-kimiċi.
Q2: Ma jissaddadx tfisser ebda rusting?
A: Le, li ma jissaddadx ifisser li mhux faċli li tikseb imtebba jew sadid, għandha kapaċità speical biex tirreżisti t-tbajja ', sadid u korrużjoni.
Q3: Tforni folji tal-istainless steel?
A: Iva, aħna nipprovdu tipi differenti ta 'folji ta' l-istainless steel, bi ħxuna tvarja minn 0.3-3.0mm. u fi finituri differenti.
Q4: Taċċetta servizz maqtugħ għal tul?
A: Naturalment, is-sodisfazzjon tal-klijent hija l-ogħla prijorità tagħna.
Q5: Jekk għandi ordni żgħira, taċċetta ordni żgħira?
A: Mhux problema, it-tħassib tiegħek huwa t-tħassib tagħna, kwantitajiet żgħar huma aċċettati.
Q6: Kif tista 'tiggarantixxi l-kwalità tal-prodott tiegħek?
A: L-ewwel, mill-bidu nett, diġà implimentajna spirtu f'moħħhom, jiġifieri l-kwalità hija l-ħajja, il-ħaddiema u l-istaff professjonali tagħna se jsegwu kull pass sakemm il-merkanzija tkun ippakkjata sew u mibgħuta 'l barra.
Q7: Se tippakkja l-prodotti?
A: Nies professjonali jagħmlu ippakkjar professjonali, għandna tipi differenti ta 'ppakkjar fakultattiv għall-klijenti, wieħed ekonomiku jew wieħed aħjar.
Q8: X'għandek tkun taf mill-klijent qabel kwotazzjoni preċiża?
A: Għal kwotazzjoni preċiża, għandna bżonn inkunu nafu l-grad, il-ħxuna, id-daqs, il-finitura tal-wiċċ, il-kulur u l-kwantità tal-ordni tiegħek, u wkoll id-destinazzjoni tal-merkanzija. Informazzjoni personalizzata dwar il-prodott se tkun meħtieġa aktar, bħal tpinġija, tqassim u pjan. Imbagħad aħna noffru kwotazzjoni kompetittiva bl-informazzjoni ta 'hawn fuq.
Q9: X'tip ta 'terminu ta' ħlas inti taċċetta?
A: Aħna naċċettaw T/T, unjoni tal-Punent, L/C.
Q10: Jekk din hija ordni żgħira, se tikkunsinna l-merkanzija lill-aġent tagħna?
A: Iva, aħna twieldu biex insolvu problemi tal-klijenti tagħna, aħna se nwasslu l-oġġetti b'mod sikur fil-maħżen tal-aġent tiegħek u nibagħtulek l-istampi.
Q11: Inti biss tagħmel folja ċatta? Irrid nagħmel fabbrikazzjoni għall-proġett il-ġdid tiegħi.
A: Le, aħna prinċipalment nipproduċu trattament tal-wiċċ tal-folja ċatta tal-istainless steel, fl-istess ħin, aħna nimanifatturaw prodott lest tal-metall apposta skont it-tpinġija u l-pjan tal-klijent, it-tekniku tagħna se jieħu ħsieb il-bqija.
Q12: Kemm-il pajjiż diġà esportajt?
A: Esportat lejn aktar minn 50 pajjiż prinċipalment mill-Amerika, ir-Russja, ir-Renju Unit, il-Kuwajt, l-Eġittu, l-Iran,
It-Turkija, il-Ġordan, eċċ.
Q13: Kif nista 'nikseb xi kampjuni?
A: Kampjuni żgħar fil-maħżen u jistgħu jipprovdu l-kampjuni b'xejn. Catalgue huwa disponibbli, il-biċċa l-kbira
mudelli għandna kampjuni lesti fl-istokk. Kampjuni personalizzati se jieħdu madwar 5-7 ijiem.
Q14: X'inhi l-kunsinna?
A: Il-ħin tal-kunsinna tal-ordni tal-kampjun huwa ta '5-7 ijiem. L-ordnijiet tal-kontejners huma madwar 15-20 jum.
Q15: X'inhi l-applikazzjoni dwar il-Prodotti tiegħek?
A: 1.elevator bieb/kabina jew u escalator's side-wall.
2.Kisi tal-ħajt ġewwa jew barra tal-kamra tal-laqgħa/ristorant.
3.Facade meta kisi fuq xi ħaġa, bħal kolonni fil-lobby.
4.Limitu fis-supermarket. 5.Decorative jiġbed f'xi postijiet ta 'divertiment.
Q16: Kemm idum Tista' Tiggarantixxi għal Dan il-Prodott/Firma?
A: Garanzija tal-kulur għal aktar minn 10 snin. Ċertifikat ta 'kwalità ta' materjali oriġinali jista '
jiġu pprovduti.
