Efere igwe anaghị agba nchara 316
Nkọwa dị mkpirikpi:
Igwe anaghị agba nchara316Nkọwa efere efere enyochagoro
Ọkọlọtọ: ASTM / ASME A240 / SA240
Nha: 1000 mm x 2000 mm, 1220 mm x 2440 mm, 1500 mm x 3000 mm, 2000 mm x 2000 mm, 2000 mm x 4000 mm
Ọkpụrụkpụ: 0.1mm ka 12mm Thk
Ụdị: Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Strip, Flat, Blank (Oghere), Mgbanaka (Flange)
Mechaa: efere akpọrepu ọkụ (HR), akwụkwọ mpịakọta oyi (CR), 2B, 2D, BA NO (8), SATIN (Met with Plastic Coated)
Isi ike: Soft, Hard, Half Hard, Quarter Hard, Spring Hard wdg.
Ọkwa SS nhataEfere 316 enyochagoro
| Ọkọlọtọ | Ọrụ NR. | UNS | JIS | BS | AFNOR | EN |
| SS 316 | 1.4401 / 1.4436 | S31600 | Sus 316 | 316S31 / 316S33 | Z7CND17-11-02 | X5CrNiMo17-12-2 / X3CrNiMo17-13-3 |
Igwe anaghị agba nchara 316 Checkered Plate Chemical Composition
| Ihe | SS 316 |
| C | 0.08 kacha |
| Mn | 2.0 kacha |
| Si | 1.0 kacha |
| P | 0.045 kacha |
| S | 0.030 kacha |
| Cr | 16-18 |
| Ni | 11-14 |
| Mo | 2-3 |
| Fe | 67.845 min |
Njirimara arụrụ arụ nke SS 316 Checkered Plate
| Ihe | SS 316 |
| Njupụta | 8.0 g/cm3 |
| Ebe mgbaze | 1400 Celsius (2550 ° F) |
| Ike ọdụdọ | Psi – 75000 , MPa – 515 |
| Ike Mpụta (0.2% kwụsịrị) | Psi – 30000 , MPa – 205 |
| Ogologo oge | 35% |
Ụdị efere SS 316 checkered
Igwe anaghị agba nchara 316 Plate Checkered
Efere Efere SS 316
A240 SS 316 Efere Efere
Efere Efere Efere UNS S31600
Ọrụ NR. 1.4401 / 1.4436 Efere Efere
2b emecha SS 316 Checkered Plate
#4 mechaa SS 316 Efere Anya
Bee na nha SS 316 Checkered Plate
SS 316 mirror mechaa efere atụnyere
#8 Mechaa efere SS 316 checkered
4 Ahịhịa mechaa SS 316 Efere Anya
Efere SS 316 Oyi a na-atụgharị
Efere SS 316 Oyi a na-atụgharị
A240 SS 316 Oyi a na-atụgharị efere
UNS S31600 Oyi Rolled Plate Checkered Plate
Ọrụ NR. 1.4401 / 1.4436 Efere a na-enyocha oyi
#4 rụchaa SS 316 Oyi a na-atụgharị akwụkwọ mpịakọta
SS 316 2b emecha efere oyi na-atụ oyi
Mbupụ Polish SS 316 CR Plate Checkered
SS 316 Hot Rolled Plates Checkered Plates
SS 316 Hot Rolled Plates Checkered Plates
A240 SS 316 Hot Rolled Checkered Plate
UNS S31600 Hot Rolled Checkered Plate
Ọrụ NR. 1.4401 / 1.4436 Ebe a na-enyocha ihe na-ekpo ọkụ
Hot Rolled #4 mechaa SS 316 Checkered Plates
SS 316 2b mecha efere ọkụ Rolled Schequered
Mbupụ Polish SS 316 HR Plates Checkered
Ọkwa ihe
| Ihe onwunwe | ASTM A240 Standard | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 4104 410S |
| ASTM A480 ọkọlọtọ | 302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615, S33228, S38100, 304H, 309H, 316H, 309H, 316H, 310H 321H,347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S312S, S3312S S32654, S32053, S31727, S33228, S34565, S35315,S31200, S31803, S32001, S32550, S31260, S32003. S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| JIS 4304-2005 ọkọlọtọ | SUS301L, SUS301J1, SUS302, SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| JIS G4305 ọkọlọtọ | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu, SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2, SUS305, SUS3301SL, SUS309S2 SUS315J1, SUS315J2, SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1, SUS316J1L, SUS317, SUS317L, SUS317LN, SUS3131JUS, SUS3131JUS SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J4L, SUS405, SUS410L, SUS429, SUS430, SUS430LX, SUS430LX, SUS43 SUS40SUS SUS436J1L, SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403, SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Nkọwapụta ngwaahịa
| Mechaa | Ọkpụrụkpụ | Njirimara | Ngwa |
| Nke 1 | 3.0mm ~ 50.0mm | Emechara ya site na mkpọgharị ọkụ, mgbakasị ahụ na pickling, nke ejiri elu na-acha ọcha mara | Ngwá ọrụ ụlọ ọrụ kemịkalụ, tankị ụlọ ọrụ |
| Nọmba 2B | 0.3mm ~ 6.0mm | Emechara ya site na ọgwụgwọ okpomọkụ, pickling mgbe oyi na-atụgharị, na-esote ahịrị ngafe akpụkpọ ahụ ka ọ na-egbuke egbuke ma dịkwa larịị | Ngwa ngwa ahụike n'ozuzu, tebụl |
| Mba. BA (Bright Annealed) | 0.5mm ~ 2.0mm | ọgwụgwọ okpomọkụ na-egbuke egbuke mgbe oyi na-atụgharị | Ngwa kichin, ngwa kichin, ebumnuche ụlọ |
| Nke 4 | 0.4mm ~ 3.0mm | Ntugharị na nọmba 150 ruo No.180 mesh abrasives. Emecha kacha ewu ewu | Ebe a na-edozi mmiri ara ehi & nri, akụrụngwa ụlọ ọgwụ, ebe ịsa ahụ |
| Nke 8 | 0.5mm ~ 2.0mm | Elu na-egosipụta enyo dị ka enyo site na iji abrasives ndị mara mma na-ekpocha ihe karịrị ntupu 800 | Reflector, mirror, Ime-Mpụga mma maka ewu |
| HL (Ahịhịa ntutu) | 0.4mm ~ 3.0mm | Emechara ya site na polishing linear na-aga n'ihu | Ihe owuwu ihe owuwu, escalators, ụgbọ ala ngwa nri kichin |
Ngwakọta kemịkalụ
| Ọkwa | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304J1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316 Ti | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C-1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904L | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Ndị ọzọ | - | - | - | - | - |
| Ego 400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420J1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420J2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436L | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440B | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3+ 3C-0.9 |
Anyịkechie ngwaahịa igwe anaghị agba nchara na akwụkwọ mgbochi nchara na mgbanaka ígwè iji gbochie mmebi.
A na-akpado akara njirimara dị ka ọkọlọtọ ọkọlọtọ ma ọ bụ ntuziaka ndị ahịa si dị.
Nkwakọ ngwaahịa pụrụ iche dị ka onye ahịa chọrọ.
ngwugwu igwe anaghị agba nchara
Mpempe mpempe akwụkwọ igwe anaghị agba nchara / igwe anaghị agba nchara
ngwugwu eriri igwe anaghị agba nchara
Ngwungwu Mbupu
Ụlọ ọrụ anyị dabeere na Wuxi, na-achịkọta obodo nke ụlọ ọrụ igwe anaghị agba nchara na China.
Anyị pụrụ iche na igwe anaghị agba nchara, mpempe akwụkwọ na efere, ọkpọkọ igwe anaghị agba nchara na akwa akwa, tubes igwe anaghị agba nchara, yana ngwaahịa aluminom na ngwaahịa ọla kọpa.
Ndị ahịa anyị sitere na Europe, America, Middle East, Africa na Southeast Asia toro ngwaahịa anyị nke ukwuu. Anyị ga-enye ndị ahịa ngwaahịa asọmpi na ọrụ zuru oke.
Ọkwa igwe anaghị agba nchara: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 316, 3, 6 420, 430, 430F, 440, 440c,
Alloy ọkwa:Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanium, Tantalum, High Speed Steel, Dị nwayọọ Steel, Aluminium, Alloy Steel, Carbon Steel, Special Nickel Alloys
N'ụdị: Ogwe gburugburu, Ogwe Square, Ogwe Hexagonal, Ogwe Flat, Angle, Channels, Profiles, Wires, Wire Rods, Sheets, Plates, Seamless Pipes, ERW Pipes, Flanges, Fittings, etc.
Q1: Gịnị bụ igwe anaghị agba nchara?
A: Igwe anaghị agba nchara pụtara enweghị akara n'elu nchara, ma ọ bụ ụdị nchara nke ikuku ma ọ bụ mmiri na-emebighị na nke na-adịghị agbanwe agba, enweghị ntụpọ, na-eguzogide ọgwụ, nchara, mmetụta na-emebi emebi nke kemịkalụ.
Q2: Igwe anaghị agba nchara ọ pụtara enweghị nchara?
A: Mba, igwe anaghị agba nchara pụtara adịghị mfe ịnweta ntụpọ ma ọ bụ nchara, ọ nwere ikike pụrụ iche iji guzogide nsị, nchara na corrosion.
Q3: Ị na-enye mpempe akwụkwọ anaghị agba nchara?
A: Ee, anyị na-enye ụdị dị iche iche nke igwe anaghị agba nchara, na ọkpụrụkpụ ranges si 0.3-3.0mm. na n'ụdị dị iche iche.
Q4: Ị na-anabata ọrụ ịkpụ n'ogologo?
A: N'ezie, afọ ojuju ndị ahịa bụ ihe kacha anyị mkpa.
Q5: Ọ bụrụ na m nwere obere usoro, ị na-anabata obere usoro?
A: Ọ bụghị nsogbu, nchegbu gị bụ nchegbu anyị, a na-anabata obere obere.
Q6: Kedu ka ị ga-esi kwe nkwa ịdị mma ngwaahịa gị?
A: Nke mbụ, site na mmalite, anyị etinyelarị mmụọ n'uche ha, nke ahụ bụ àgwà bụ ndụ, ndị ọrụ ọkachamara anyị na ndị ọrụ ga-agbaso nzọụkwụ ọ bụla ruo mgbe ngwongwo ndị ahụ na-akwakọba nke ọma ma bupu ya.
Q7: Ị ga-akwakọba ngwaahịa?
A: Ndị ọkachamara na-eme nkwakọ ngwaahịa ọkachamara, anyị nwere ụdị nkwakọ ngwaahịa dị iche iche maka ndị ahịa, otu akụ na ụba ma ọ bụ ka mma.
Q8: Kedu ihe ị chọrọ ịma site n'aka ndị ahịa tupu nkwupụta ziri ezi?
A: Maka nkọwa ziri ezi, anyị kwesịrị ịma ọkwa, ọkpụrụkpụ, nha, imecha elu, agba na ọnụ ọgụgụ nke ihe ị chọrọ, yana ebe ị na-aga. A ga-achọkwu ozi ngwaahịa ahaziri ahazi, dị ka eserese, nhazi na atụmatụ. Mgbe ahụ, anyị ga-enye nhota asọmpi na ozi dị n'elu.
Q9: Kedu ụdị ụgwọ ịkwụ ụgwọ ị na-anabata?
A: Anyị na-anabata T/T, West union, L/C.
Q10: Ọ bụrụ na nke a bụ obere iwu, ị ga-ebugara ndị ọrụ anyị ngwongwo ndị ahụ?
A: Ee, a mụrụ anyị iji dozie nsogbu nke ndị ahịa anyị, anyị ga-enweta ngwongwo ahụ n'enweghị nsogbu na ụlọ nkwakọba ihe nke onye ọrụ gị ma ziga gị foto.
Q11: Ị na-eme mpempe akwụkwọ dị larịị? Achọrọ m ịmebe echiche maka ọrụ ọhụrụ m.
A: Ee e, anyị tumadi na-emepụta igwe anaghị agba nchara ewepụghị mpempe akwụkwọ n'elu ọgwụgwọ, n'otu oge ahụ, anyị rụpụta ahaziri metal okokụre ngwaahịa dị ka kwa ahịa ịbịaru na atụmatụ, anyị technician ga-elekọta ndị ọzọ.
Q12: Ugboro ole ka i bupuburu?
A: Ebupụ ya karịa mba 50 tumadi site na America, Russia, UK, Kuwait, Egypt, Iran,
Turkey, Jordan, wdg.
Q13: Kedu ka m ga-esi nweta ụfọdụ nlele?
A: Obere ihe nlele na-echekwa ma nwee ike ịnye ihe nlele n'efu. Catalgue dị, ọtụtụ
ụkpụrụ anyị nwere njikere samples na ngwaahịa. Ihe nlele ahaziri ahazi ga-ewe ihe dịka ụbọchị 5-7.
Q14: Gịnị bụ nnyefe?
A: Oge nnyefe nke ihe nlele bụ ụbọchị 5-7. Ngwunye akpa bụ ihe dịka ụbọchị 15-20.
Q15: Gịnị bụ ngwa gbasara ngwaahịa gị?
A: 1. elevator ọnụ ụzọ / ụlọ ma ọ bụ na escalator's n'akụkụ mgbidi.
2.Mgbidi mkpuchi n'ime ma ọ bụ n'èzí nzukọ ụlọ / ụlọ oriri na ọṅụṅụ.
3.Facade mgbe cladding n'elu ihe, dị ka ogidi na n'ọnụ ụlọ.
4.Ciling na nnukwu ụlọ ahịa. 5.Decorative adọta na ụfọdụ ntụrụndụ ebe.
Q16: Ogologo oge ole ka ị nwere ike ikwe nkwa maka ngwaahịa a / mechaa?
A: Agba nkwa maka ihe karịrị afọ 10. Asambodo ogo ihe izizi nwere ike
ka enyere.
