Factory For Casting 304 Stainless Steel Union - ALUMINUM ROUNDS 2017-T451, 2017-T4 – Cepheus

Short Description:

Send email to us Download as PDF

Product Detail

Technical Specification

Product Package & Shipment

Company Introduction

Question & Answers

Product Tags

Feedback (2)

We insist on the principle of development of 'High quality, Efficiency, Sincerity and Down-to-earth working approach' to deliver you with great provider of processing for 430 Stainless Steel Tube , 904l Round Bar , Hairline Stainless Steel Sheet , We attend seriously to produce and behave with integrity, and by the favor of customers at home and abroad in the xxx industry.

Factory For Casting 304 Stainless Steel Union - ALUMINUM ROUNDS 2017-T451, 2017-T4 – Cepheus Detail:

2014/2017/2024 T6/T651 High Hardness Aluminum Alloy Bar Aluminum Bar

2024 aluminum bar, aluminum rod is a typical hard aluminum alloy in the aluminum-copper-magnesium series. Its composition is reasonable and its comprehensive performance is good. This alloy is produced in many countries and is the largest amount of hard aluminum.

The alloy can be used as working parts below 150 ° C. The strength of 2024 alloy is higher than that of 7075 alloy. The forming performance is better in the hot state, annealing and new quenching states, and the heat treatment strengthening effect is significant, but the heat treatment process is strict. Poor corrosion resistance, but covered with pure aluminum can be effectively protected; cracks are easy to occur during welding, but special processes can be used for welding and riveting.

2024 aluminum bar,aluminum rod is a high-strength hard aluminum, which can be strengthened by heat treatment. It has moderate plasticity in the quenched and freshly quenched state. It has good spot welding and has the tendency to form intergranular cracks when gas welding. The cutting performance is good, and the machinability after annealing is low: the corrosion resistance is not high. Anodizing treatment and painting methods are often used or the surface is coated with an aluminum layer to improve its corrosion resistance.

2024 is mainly used to make various high-load parts and components (but not including stamping parts and forgings) such as skeleton parts, skins, bulkheads, ribs, spar, rivets and other working parts below 150 ºC on aircraft.

Chemical Composition

Alloy	Si	Fe	Cu	Mn	Mg	Cr	Zn	Ti	Al
2024	0.5	0.5	3.8-4.9	0.3-0.9	1.2-1.8	0.10	0.25	0.15	remain

Mechanical Properties

Aluminum Alloy & Temperature	Tensile Strength (Rm/MPa)	Proof Strength (Rp0.20/Mpa)	Percentage Elongation (%)	Hardness (HB)
2024	470	325	10	120

Product detail pictures:

Being supported by an advanced and professional IT team, we could offer technical support on pre-sales & after-sales service for Factory For Casting 304 Stainless Steel Union - ALUMINUM ROUNDS 2017-T451, 2017-T4 – Cepheus, The product will supply to all over the world, such as: Uruguay, Indonesia, Ireland, We warmly welcome domestic and overseas customers to visit our company and have business talk. Our company always insists on the principle of "good quality, reasonable price, the first-class service". We have been willing to build long-term, friendly and mutually beneficial cooperation with you.

Material Grade

Material	ASTM A240 Standard	201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410S 430 904L
	ASTM A480 Standard	302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615,S33228, S38100, 304H, 309H, 310H, 316H, 309HCb, 310HCb, 321H,347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S33228, S34565, S35315,S31200, S31803, S32001, S32550, S31260, S32003, S32101,S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974
	JIS 4304-2005 Standard	SUS301L,SUS301J1,SUS302,SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630
	JIS G4305 Standard	SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu,SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2,SUS305, SUS309S, SUS310S, SUS312L, SUS315J1, SUS315J2,SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1,SUS316J1L,SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2,SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J4L, SUS405, SUS410L, SUS429, SUS430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L,SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403,SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A

Product Specification

Finish	Thickness	Characteristics	Applications
No. 1	3.0mm~50.0mm	Finished by hot-rolling, annealing and pickling, characterized by white pickled surface	Chemical industry equipment, Industrial tanks
No. 2B	0.3mm~6.0mm	Finished by heat treatment, pickling after cold rolling, followed by skin pass line to be more brighter and smooth surface	General Application Medical Instruments, Tableware
No. BA (Bright Annealed)	0.5mm~2.0mm	Bright heat treatment after cold rolling	Kitchen utensil, kitchen ware, architectural purpose
No. 4	0.4mm~3.0mm	Polishing with No. 150 to No.180 mesh abrasives. The most popular finishes	Milk & Food processing facilities, Hospital Equipment, Bath-tub
No. 8	0.5mm~2.0mm	A mirror-like reflective surface by polishing with finer abrasives over 800 mesh	Reflector, Mirror, Interior-Exterior decoration forbuilding
HL(Hair Line)	0.4mm~3.0mm	Finished by continuous linear polishing	Architectural purposes, escalators, kitchen ware vehicles

Chemical Composition

Grade	C	Si	Mn	P	S	Cr	Ni	Mo	Ti	N	Cu	Nb
201	≤0.15	≤1.0	5.50-7.50	≤0.05	≤0.03	16.00-18.00	3.50-5.50	-	-	0.05-0.25	-	-
202	≤0.15	≤1.0	7.50-10.00	≤0.05	≤0.03	17.00-19.00	4.00-6.00	-	-	0.05-0.25	-	-
301	≤0.15	≤1.0	≤2.0	≤0.045	≤0.03	16.00-18.00	6.00-8.00	-	-	≤0.1	-	-
302	≤0.15	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	8.00-10.00	-	-	≤0.1	-	-
303	≤0.15	≤1.0	≤2.0	≤0.2	≥0.15	17.00-19.00	8.00-10.00	≤0.6	-	≤0.1	-	-
304	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	8.00-10.00	-	-	-	-	-
304L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	-	-	-
304H	0.04-0.1	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	-	-	-
304N	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	0.10-0.16	-	-
304J1	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	6.00-9.00	-	-	-	1.00-3.00	-
305	≤0.12	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	10.50-13.00	-	-	-	-	-
309S	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	22.00-24.00	12.00-15.00	-	-	-	-	-
310S	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	24.00-26.00	19.00-22.00	-	-	-	-	-
316	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	-	-	-
316L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	12.00-15.00	2.00-3.00	-	-	-	-
316H	≤0.1	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	-	-	-
316N	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	0.10-0.16	-	-
316Ti	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	16.00-19.00	11.00-14.00	2.00-3.00	≥5C	-	-	-
317L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	11.00-15.00	3.00-4.00	-	-	-	-
321	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	5C-0.7	-	-	-
347	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	-	-	-	10C-1.10
347H	≤0.1	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	-	-	-	8C-1.10
2205	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	21.00-24.00	4.50-6.50	2.50-3.50	-	0.08-0.20	-	-
2507	≤0.03	≤0.8	≤1.2	≤0.035	≤0.02	24.00-26.00	6.00-8.00	3.00-5.00	-	0.24-0.32	-	-
904L	≤0.02	≤1.0	≤2.0	≤0.045	≤0.03	19.00-23.00	23.00-28.00	4.00-5.00	-	-	1.00-2.00	-
C276	≤0.02	≤0.05	≤1.0	-	-	14.00-16.50	Other	-	-	-	-	-
Monel400	≤0.3	≤0.5	≤2.0	-	≤0.024	-	≥63	-	-	-	28-34	-
409L	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	17.00-19.00	-	-	-	-	-	-
410	≤0.15	≤1.0	≤1.0	≤0.035	≤0.03	11.50-13.50	-	-	-	-	-	-
410L	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	11.50-13.50	-	-	-	-	-	-
420J1	0.16-0.25	≤1.0	≤1.0	≤0.035	≤0.03	12.00-14.00	-	-	-	-	-	-
420J2	0.26-0.40	≤1.0	≤1.0	≤0.035	≤0.03	12.00-14.00	-	-	-	-	-	-
430	≤0.12	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	-	-	-	-	-
436L	≤0.025	≤1.0	≤1.0	≤0.035	≤0.03	16.00-19.00	-	-	-	-	-	-
439	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	-	-	-	-	-
440A	0.60-0.75	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
440B	0.75-0.95	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
440C	0.95-1.2	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
441	≤0.03	0.2-0.8	≤0.7	≤0.03	≤0.015	17.50-18.50	-	≤0.5	0.1-0.5	≤0.025	-	0.3+3C-0.9

We wrap the stainless steel products with anti-rust paper and steel rings to prevent damage.

Identification labels are tagged accordingto standard specification or customer’s instructions.

Special packing is available as per customer’s requirement.

Stainless Steel Coil Package

Stainless Steel Sheet / Stainless Steel Plate Package

Stainless Steel Strip Package

Shipment Package

Our company is based in Wuxi, gathering city of industrial stainless steel in China.

We specialized in stainless coils, sheets and plate, stainless steel pipe and fittings, stainless steel tubes, and also aluminum products and copper products.

Our products have been highly praised by our clients from Europe, America, the Middle East, African and Southeast Asia. We will offer competitive products and comprehensive service to customers.

Stainless Steel Grade: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 316L, 321, 347, 410, 416, 420, 430, 430F, 440, 440c,

Alloy Grade :Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanium, Tantalum, High Speed Steel, Mild Steel, Aluminium, Alloy Steel, Carbon Steel, Special Nickel Alloys

In form of : Round Bars, Square Bars, Hexagonal Bars, Flat Bars, Angles, Channels, Profiles, Wires, Wire Rods, Sheets, Plates, Seamless Pipes, ERW Pipes, Flanges, Fittings,etc.

Q1: What is stainless?

A: Stainless means no marks on the steel surface, or a kind of steel that is not damaged by air or water and that does not change color, spotless, resistant to staining, rusting, the corrosive effect of chemicals.

Q2: Does stainless mean no rusting?

A: No, stainless means not easy to get stained or rusty, it has speical ability to reisist staining, rusting and corrosion.

Q3: Do you supply stainless steel sheets?

A: Yes, we supply different types of stainless steel sheets, with thickness ranges from 0.3-3.0mm. and in different finishes.

Q4: Do you accept cut to length service?

A: Of course, customer’s satisfaction is our top priority.

Q5: If i have a small order, do you accept small order?

A: Not a problem, your concern is our concern, small quantities are accepted.

Q6: How can you guarantee your product quality?

A: First, from the very start, we have already implemented a spirit to their mind, that is quality is life, our professional workers and staffs will follow up every step till the goods packed well and shipped out.

Q7: Will you pack the products?

A: Professional people do professional packing, we have different types of packing optional to customers, economic one or better one.

Q8: What do you need to know from customer before accurate quotation?

A: For an accurate quotation, we need to know grade, thickness, size, surface finish, color and quantity of your order, and also the destination of the goods. Customized product information will be needed more, like drawing, layout and plan. Then we will offer competitive quotation with the above information.

Q9: What kind of payment term you accpet?

A: We accept T/T, West union, L/C.

Q10: If this is a small order, will you delivery the goods to our agent?

A: Yes, we are born to solve problems of our customers, we will get the goods safely to your agent’s warehouse and send you the pictures.

Q11: Do you just make flat sheet? I want to make a fabrication for my new project.

A: No, we mainly produce stainless steel flat sheet surface treatment, at the same time, we manufacture customized metal finished product as per customer’s drawing and plan, our technician will take care of the rest.

Q12: How many coutries you already exported ?
A: Exported to more than 50 countries mainly from America, Russia, UK, Kuwait, Egypt, Iran,
Turkey, Jordan, etc.
Q13: How can I get some samples?
A: Small samples in store and can provide the samples for free. Catalgue is available, most
patterns we have ready samples in stock. Customized samples will take about 5-7days.
Q14: What is the delivery ?
A: Sample order’s delivery time is 5- 7 days. Container orders are about 15-20 days.

Q15: What is the application about your Products?
A: 1.elevator door/cabin or and escalator’s side-wall.
2.Wall cladding inside or outside meeting room/ restaurant.
3.Facade when cladding over something, like columns in the lobby.
4.Ceiling in the supermarket. 5.Decorative draws in some entertainment places.
Q16: How long Can You Guarantee for This Product/Finish?
A: Color guarantee for more than 10 years. Original materials quality certificate can
be provided.