Aloi nicel-copr MONEL 400 (UNS N04400/. W.Nr. 2.4360 a 2.4361)
Disgrifiad Byr:
Rydym yn cyflenwi ac yn allforio deunydd dur di-staen Monel 400 Round Bar mewn ystod eang, siâp a maint
→ Monel 400 Bar Rownd Rownd Bariau
→ Monel 400 Bar Rownd Sgwâr Bar
→ Bariau Fflat Bar Rownd Monel 400
→ Monel 400 Bar Rownd Threaded Bar
Monel 400Bar Rownd Dur Di-staen,
Bar Rownd Dur Di-staen,
Dur di-staen wedi'i rolio'n boeth ac ongl Anealed & Piclo:
Maint sydd ar gael:
| Lled(mm) | Trwch (mm) | ||||
| 20*20 | 3 | ||||
| 25*25 | 3 | 4 | 5 | ||
| 30*30 | 3 | 4 | 5 | ||
| 40*40 | 3 | 4 | 5 | 6 | |
| 50*50 | 3 | 4 | 5 | 6 | 7 |
| 60*60 | 5 | 6 | 7 | 8 | |
| 65*65 | 5 | 6 | 7 | 8 | |
| 70*70 | 6 | 7 | 8 | 9 | 10 |
| 75*75 | 6 | 7 | 8 | 9 | 10 |
| 80*80 | 7 | 8 | 9 | 10 | |
| 100*100 | 8 | 9 | 10 | 12 | |
2.Stainless dur U sianel
Sianel U rholio poeth Meintiau sydd ar gael (mm):
| Trwch | Uchder | Lled | ||
| 3 | 5 | 6 | 80 | 40 |
| 4 | 5 | 6 | 100 | 50 |
| 5 | 6 | 7 | 120 | 50 |
| 6 | 7 | 140 | 60 | |
Sianel U wedi'i Weldio Meintiau sydd ar gael (mm):
| Trwch | Uchder | Lled | |||||||||||||||
| 3 | 4 | 5 | 50 | 55 | 60 | 65 | 70 | 75 | 25 | ||||||||
| 3 | 4 | 5 | 60 | 65 | 70 | 75 | 80 | 30 | |||||||||
| 3 | 4 | 5 | 80 | 85 | 90 | 95 | 100 | 105 | 110 | 115 | 120 | 125 | 130 | 135 | 140 | 145 | 40 |
| 150 | 155 | 160 | 165 | 170 | 175 | 180 | |||||||||||
| 4 | 5 | 6 | 100 | 105 | 110 | 115 | 120 | 125 | 135 | 140 | 145 | 150 | 155 | 160 | 50 | ||
| 165 | 170 | 175 | 180 | 185 | 190 | 195 | 200 | 205 | 210 | 215 | 220 | ||||||
| 5 | 6 | 7 | 120 | 125 | 130 | 135 | 140 | 145 | 150 | 155 | 160 | 165 | 170 | 175 | 180 | 60 | |
| 185 | 190 | 195 | 200 | 205 | 210 | 215 | 220 | 225 | 230 | 235 | 240 | ||||||
| 6 | 7 | 8 | 140 | 145 | 150 | 155 | 160 | 165 | 170 | 175 | 180 | 185 | 190 | 200 | 70 | ||
| 205 | 210 | 215 | 220 | 225 | 230 | 235 | 240 | 245 | 250 | 255 | 260 | ||||||
| 6 | 7 | 9 | 150 | 155 | 160 | 165 | 170 | 175 | 180 | 185 | 190 | 195 | 200 | 205 | 210 | 75 | |
| 215 | 220 | 225 | 230 | 235 | 240 | 245 | 250 | 255 | 260 | 265 | 270 | ||||||
| 7 | 8 | 10 | 160 | 165 | 170 | 175 | 180 | 185 | 190 | 195 | 200 | 205 | 210 | 215 | 220 | 80 | |
| 225 | 230 | 235 | 240 | 245 | 250 | 255 | 260 | 265 | 270 | 275 | 289 | ||||||
| 8 | 9 | 12 | 200 | 205 | 210 | 215 | 220 | 225 | 235 | 240 | 245 | 250 | 255 | 260 | 100 | ||
| 265 | 270 | ||||||||||||||||
Cyfansoddiad cemegol
| Gradd | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304J1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316Ti | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C- 1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904L | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Arall | - | - | - | - | - |
| Monel400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420J1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420J2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436L | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440B | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3+3C-0.9 |
Gradd Deunydd
| Deunydd | Safon ASTM A240 | 201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410S 4 |
| Safon ASTM A480 | 302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615, S33228, S38100, 304H, 309H, 3193H, H.C. 347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S333251, S333250, S333250 03, S32001, S32550, S31260, S32003, S32101, S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974 | |
| Safon JIS 4304-2005 | SUS301L, SUS301J1, SUS302, SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630 | |
| Safon JIS G4305 | SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu, SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2, SUS305, SUS319S, SUS311S 315J2, SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1, SUS316J1L, SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2, SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3JL, SUS, SUS24L, SUS329J3JL4, SUS430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L, SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403, SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A |
Manyleb Cynnyrch
| Gorffen | Trwch | Nodweddion | Ceisiadau |
| Rhif 1 | 3.0mm ~ 50.0mm | Wedi'i orffen gan rolio poeth, anelio a phiclo, a nodweddir gan wyneb piclo gwyn | Offer diwydiant cemegol, tanciau diwydiannol |
| Rhif 2B | 0.3mm ~ 6.0mm | Wedi'i orffen gan driniaeth wres, piclo ar ôl rholio oer, ac yna llinell basio croen i fod yn fwy disglair ac arwyneb llyfn | Offerynnau Meddygol Cymhwysiad Cyffredinol, Llestri |
| Rhif BA (Bright Annealed) | 0.5mm ~ 2.0mm | Triniaeth wres llachar ar ôl rholio oer | Offer cegin, nwyddau cegin, pwrpas pensaernïol |
| Rhif 4 | 0.4mm ~ 3.0mm | sgleinio gyda sgraffinyddion rhwyll Rhif 150 i No.180. Y gorffeniadau mwyaf poblogaidd | Cyfleusterau prosesu Llaeth a Bwyd, Offer Ysbyty, twb Bath |
| Rhif 8 | 0.5mm ~ 2.0mm | Arwyneb adlewyrchol tebyg i ddrych trwy sgleinio â sgraffinyddion manach dros 800 o rwyll | Adlewyrchydd, Drych, Addurno Mewnol-Tu allan ar gyfer adeiladu |
| HL(Gwallt Llinell) | 0.4mm ~ 3.0mm | Wedi'i orffen trwy sgleinio llinellol parhaus | Dibenion pensaernïol, grisiau symudol, cerbydau nwyddau cegin |
Cyfansoddiad Cemegol
| Gradd | C | Si | Mn | P | S | Cr | Ni | Mo | Ti | N | Cu | Nb |
| 201 | ≤0.15 | ≤1.0 | 5.50-7.50 | ≤0.05 | ≤0.03 | 16.00-18.00 | 3.50-5.50 | - | - | 0.05-0.25 | - | - |
| 202 | ≤0.15 | ≤1.0 | 7.50-10.00 | ≤0.05 | ≤0.03 | 17.00-19.00 | 4.00-6.00 | - | - | 0.05-0.25 | - | - |
| 301 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 16.00-18.00 | 6.00-8.00 | - | - | ≤0.1 | - | - |
| 302 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | ≤0.1 | - | - |
| 303 | ≤0.15 | ≤1.0 | ≤2.0 | ≤0.2 | ≥0.15 | 17.00-19.00 | 8.00-10.00 | ≤0.6 | - | ≤0.1 | - | - |
| 304 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 8.00-10.00 | - | - | - | - | - |
| 304L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304H | 0.04-0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | - | - | - |
| 304N | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 8.00-10.00 | - | - | 0.10-0.16 | - | - |
| 304J1 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 6.00-9.00 | - | - | - | 1.00-3.00 | - |
| 305 | ≤0.12 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 10.50-13.00 | - | - | - | - | - |
| 309S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 22.00-24.00 | 12.00-15.00 | - | - | - | - | - |
| 310S | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 24.00-26.00 | 19.00-22.00 | - | - | - | - | - |
| 316 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 12.00-15.00 | 2.00-3.00 | - | - | - | - |
| 316H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | - | - | - |
| 316N | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | 10.00-14.00 | 2.00-3.00 | - | 0.10-0.16 | - | - |
| 316Ti | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | 11.00-14.00 | 2.00-3.00 | ≥5C | - | - | - |
| 317L | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 18.00-20.00 | 11.00-15.00 | 3.00-4.00 | - | - | - | - |
| 321 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | 5C-0.7 | - | - | - |
| 347 | ≤0.08 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 10C-1.10 |
| 347H | ≤0.1 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | 9.00-12.00 | - | - | - | - | 8C- 1.10 |
| 2205 | ≤0.03 | ≤1.0 | ≤2.0 | ≤0.035 | ≤0.03 | 21.00-24.00 | 4.50-6.50 | 2.50-3.50 | - | 0.08-0.20 | - | - |
| 2507 | ≤0.03 | ≤0.8 | ≤1.2 | ≤0.035 | ≤0.02 | 24.00-26.00 | 6.00-8.00 | 3.00-5.00 | - | 0.24-0.32 | - | - |
| 904L | ≤0.02 | ≤1.0 | ≤2.0 | ≤0.045 | ≤0.03 | 19.00-23.00 | 23.00-28.00 | 4.00-5.00 | - | - | 1.00-2.00 | - |
| C276 | ≤0.02 | ≤0.05 | ≤1.0 | - | - | 14.00-16.50 | Arall | - | - | - | - | - |
| Monel400 | ≤0.3 | ≤0.5 | ≤2.0 | - | ≤0.024 | - | ≥63 | - | - | - | 28-34 | - |
| 409L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 17.00-19.00 | - | - | - | - | - | - |
| 410 | ≤0.15 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 410L | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 11.50-13.50 | - | - | - | - | - | - |
| 420J1 | 0.16-0.25 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 420J2 | 0.26-0.40 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 12.00-14.00 | - | - | - | - | - | - |
| 430 | ≤0.12 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 436L | ≤0.025 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-19.00 | - | - | - | - | - | - |
| 439 | ≤0.03 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | - | - | - | - | - |
| 440A | 0.60-0.75 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440B | 0.75-0.95 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 440C | 0.95-1.2 | ≤1.0 | ≤1.0 | ≤0.035 | ≤0.03 | 16.00-18.00 | - | ≤0.75 | - | - | - | - |
| 441 | ≤0.03 | 0.2-0.8 | ≤0.7 | ≤0.03 | ≤0.015 | 17.50-18.50 | - | ≤0.5 | 0.1-0.5 | ≤0.025 | - | 0.3+3C-0.9 |
Rydym nilapio'r cynhyrchion dur di-staen gyda phapur gwrth-rhwd a modrwyau dur i atal difrod.
Mae labeli adnabod yn cael eu tagio yn unol â manyleb safonol neu gyfarwyddiadau cwsmeriaid.
Mae pacio arbennig ar gael yn unol â gofynion y cwsmer.
Pecyn Coil Dur Di-staen
Taflen Dur Di-staen / Pecyn Plât Dur Di-staen
Pecyn Stribed Dur Di-staen
Pecyn Cludo
Mae ein cwmni wedi'i leoli yn Wuxi, gan gasglu dinas o ddur di-staen diwydiannol yn Tsieina.
Fe wnaethom arbenigo mewn coiliau, cynfasau a phlât di-staen, pibell ddur di-staen a ffitiadau, tiwbiau dur di-staen, a hefyd cynhyrchion alwminiwm a chynhyrchion copr.
Mae ein cynnyrch wedi cael canmoliaeth uchel gan ein cleientiaid o Ewrop, America, y Dwyrain Canol, Affrica a De-ddwyrain Asia. Byddwn yn cynnig cynnyrch cystadleuol a gwasanaeth cynhwysfawr i gwsmeriaid.
Dur Di-staen Gradd: 201, 202, 202cu, 204, 204cu, 303, 304, 304L, 308, 308L, 309, 309s, 310, 310s, 316, 316L, 3, 20, 3, 3, 3, 4, 3, 3, 3, 3, 3, 4, 3, 430F, 440, 440c,
Gradd Aloi: Monel, Inconel, Hastolley, Duplex, Super Duplex, Titanium, Tantalum, Dur Cyflymder Uchel, Dur Ysgafn, Alwminiwm, Dur Aloi, Dur Carbon, Aloion Nicel Arbennig
Ar ffurf: Bariau Crwn, Bariau Sgwâr, Bariau Hecsagonol, Bariau Fflat, Onglau, Sianeli, Proffiliau, Gwifrau, Gwialenni Gwifren, Taflenni, Platiau, Pibellau Di-dor, Pibellau ERW, Flanges, Ffitiadau, ac ati.
C1: Beth yw di-staen?
A: Mae di-staen yn golygu dim marciau ar yr wyneb dur, neu fath o ddur nad yw'n cael ei niweidio gan aer neu ddŵr ac nad yw'n newid lliw, di-staen, gwrthsefyll staenio, rhydu, effaith cyrydol cemegau.
C2: A yw di-staen yn golygu dim rhydu?
A: Na, mae di-staen yn golygu nad yw'n hawdd cael ei staenio neu ei rydu, mae ganddo allu arbennig i wrthsefyll staenio, rhydu a chorydiad.
C3: A ydych chi'n cyflenwi dalennau dur di-staen?
A: Ydym, rydym yn cyflenwi gwahanol fathau o ddalennau dur di-staen, gyda thrwch yn amrywio o 0.3-3.0mm. ac mewn gwahanol derfyniadau.
C4: A ydych chi'n derbyn gwasanaeth torri hyd?
A: Wrth gwrs, boddhad cwsmeriaid yw ein prif flaenoriaeth.
C5: Os oes gennyf orchymyn bach, a ydych chi'n derbyn archeb fach?
A: Ddim yn broblem, eich pryder yw ein pryder, derbynnir symiau bach.
C6: Sut allwch chi warantu ansawdd eich cynnyrch?
A: Yn gyntaf, o'r cychwyn cyntaf, rydym eisoes wedi gweithredu ysbryd i'w meddwl, hynny yw ansawdd bywyd, bydd ein gweithwyr proffesiynol a'n staff yn dilyn pob cam nes bod y nwyddau wedi'u pacio'n dda a'u cludo allan.
C7: A fyddwch chi'n pacio'r cynhyrchion?
A: Mae pobl broffesiynol yn pacio proffesiynol, mae gennym wahanol fathau o bacio yn ddewisol i gwsmeriaid, un economaidd neu un gwell.
C8: Beth sydd angen i chi ei wybod gan y cwsmer cyn dyfynbris cywir?
A: I gael dyfynbris cywir, mae angen i ni wybod gradd, trwch, maint, gorffeniad wyneb, lliw a maint eich archeb, a hefyd cyrchfan y nwyddau. Bydd angen mwy o wybodaeth am gynnyrch wedi'i haddasu, fel lluniadu, gosodiad a chynllun. Yna byddwn yn cynnig dyfynbris cystadleuol gyda'r wybodaeth uchod.
C9: Pa fath o dymor talu rydych chi'n ei dderbyn?
A: Rydym yn derbyn T / T, undeb y Gorllewin, L / C.
C10: Os yw hwn yn orchymyn bach, a fyddwch chi'n danfon y nwyddau i'n hasiant?
A: Ydym, rydym yn cael ein geni i ddatrys problemau ein cwsmeriaid, byddwn yn cael y nwyddau'n ddiogel i warws eich asiant ac yn anfon y lluniau atoch.
C11: A ydych chi'n gwneud dalen fflat yn unig? Rwyf am wneud gwneuthuriad ar gyfer fy mhrosiect newydd.
A: Na, rydym yn bennaf yn cynhyrchu triniaeth wyneb dalen fflat dur di-staen, ar yr un pryd, rydym yn cynhyrchu cynnyrch gorffenedig metel wedi'i addasu yn unol â llun a chynllun y cwsmer, bydd ein technegydd yn gofalu am y gweddill.
C12: Faint o wledydd y gwnaethoch chi eu hallforio eisoes?
A: Wedi'i allforio i fwy na 50 o wledydd yn bennaf o America, Rwsia, y DU, Kuwait, yr Aifft, Iran,
Twrci, Iorddonen, ac ati.
C13: Sut alla i gael rhai samplau?
A: Samplau bach yn y siop a gallant ddarparu'r samplau am ddim. Mae catalog ar gael, y rhan fwyaf
patrymau mae gennym samplau parod mewn stoc. Bydd samplau wedi'u haddasu yn cymryd tua 5-7 diwrnod.
C14: Beth yw'r cyflenwad?
A: Amser cyflwyno archeb sampl yw 5-7 diwrnod. Mae archebion cynhwysydd tua 15-20 diwrnod.
C15: Beth yw'r cais am eich Cynhyrchion?
A: Drws/caban 1.elevator neu wal ochr grisiau symudol.
2. Cladin wal y tu mewn neu'r tu allan i ystafell gyfarfod/bwyty.
3.Facade wrth gladin dros rywbeth, fel colofnau yn y lobi.
4.Ceiling yn yr archfarchnad. 5.Decorative yn tynnu mewn rhai mannau adloniant.
C16: Pa mor hir y gallwch chi ei warantu ar gyfer y cynnyrch / gorffeniad hwn?
A: Gwarant lliw am fwy na 10 mlynedd. Gall tystysgrif ansawdd deunyddiau gwreiddiol
cael ei ddarparu.
